如果用户的显示卡是S3/Mach32/Mach8/8514/P9000/AGX/W32/S3 Virge系列就可以在第四个选项中挑选自己的服务器，否则只能选择3，使用256色了。如果连选3都无法正常启动X-WINDOW，那你只有选2，享用那丑陋的16色了，要么就只能换块卡了。像笔者的Trident9685，只能选3，忍受那平谈无奇的256色。接下来它会问你要不要做连接! 请选Y
Please answer the following question with either 'y' or 'n'.
Do you want me to set the symbolic link?
|
然后它问你:Do you want to set it in /var/X11R6/bin?是否存盘，当然回答Y了。
显存大小:
How much video memory do you have on your video card:
1 256K
2 512K
3 1024K
4 2048K
5 4096K
6 Other
Enter your choice:
|
我的显卡有2MB的显存，所以选4 !又是厂牌和型号, 随便给它几个英文字就可以了!象我索性送几个回车给它。 接下来是RAMDAC chip的设定...
The RAMDAC setting only applies to the S3 and AGX servers. Some RAMDAC's are
auto-detected by the server. The detection of a RAMDAC is forced by using a
Ramdac "identifier" line in the Device section. The identifiers are shown
at the right of the following table of RAMDAC types:
1 AT&T 20C490 (S3 server) att20c490
2 AT&T 20C498/21C498/22C498 (S3) att20c498
3 AT&T 20C505 (S3) att20c505
4 BrookTree BT481 (AGX) bt481
5 BrookTree BT482 (AGX) bt482
6 BrookTree BT485/9485 (S3) bt485
7 Sierra SC15025 (S3, AGX) sc15025
8 S3 GenDAC (86C708) (autodetected) s3gendac
9 S3 SDAC (86C716) (autodetected) s3_sdac
10 STG-1700 (S3) stg1700
11 TI 3020 (S3) ti3020
12 TI 3025 (S3) ti3025
13 Normal DAC normal
Just press enter if you don't want a Ramdac setting.
What Ramdac setting do you want (1-13)?
|
有说明书，可以对照说明书，但我建议有最省事的方法，按个q键，让它自己查。 再下来就是最讨厌的Clock chip的设定了：
A Clockchip line in the Device section forces the detection of a
programmable clock device. With a clockchip enabled, any required
clock can be programmed without requiring probing of clocks or a
Clocks line. Most cards don't have a programmable clock chip.
Choose from the following list:
1 Chrontel 8391 (uncertain at the time of writing) ch8391
2 ICD2061A and compatibles (ICS9161A, DCS2824) icd2061a
3 ICS2595 ics2595
4 ICS5342 (similar to SDAC, but not completely compatible) ics5342
5 S3 GenDAC (86C708) and ICS5300 (autodetected) s3gendac
6 S3 SDAC (86C716) s3_sdac
7 Sierra SC11412 sc11412
8 TI 3025 ti3025
Just press enter if you don't want a Clockchip setting.
What Clockchip setting do you want (1-8)?
|
由于说明书常常不写出这颗芯片的型号，所以......唉，天无绝人之路，按下回车键，等待它自己去检测吧！注意盯着屏幕，当屏幕上出现：Do you want me to run 'X-probeonly' now?一定要按Y，否则，它就不会做检测了。 最后就是选择显示模式:
For each depth, a list of modes (resolutions) is defined. The default
resolution that the server will start-up with will be the first listed
mode that can be supported by the monitor and card.
Currently it is set to:
"640x480" "800x600" "1024x768" "1280x1024" for 8bpp
"640x480" "800x600" "1024x768" for 16bpp
"640x480" "800x600" for 32bpp
Note that 16bpp and 32bpp are only supported on a few configurations.
Modes that cannot be supported due to monitor or clock constraints will
be automatically skipped by the server.
1 Change the modes for 8pp (256 colors)
2 Change the modes for 16bpp (32K/64K colors)
3 Change the modes for 32bpp (24-bit color)
4 The modes are OK, continue.
Enter your choice:
|
干脆，一个回车完事。反正没多大用处。 然后屏幕提示：Shall I write it to /etc/XF86Config?输入Y，存盘结束。 终於完成了!真是劳神伤身，惊心动魄的时候到了。输入startx。如果你看到漂亮的Xwindow，那么祝贺你大功告成了。否则，真是悲惨世界:-<，大侠请重新来过。只好让你根据上面的介绍再配一遍吧。
其实，X-Win由两个部分组成：X服务器和窗口管理器。上面我们配置的就是X服务器，我们还应该学会为X-WIN改改面孔，才能真正随心所欲装点自己的LINUX哦。
